CHEMISTRY GLOSSARY

thermal conductivity    →   toplinska vodljivost

Thermal conductivity (Λ) is rate of heat flow divided by the area and by the temperature gradient.

conductivity    →   vodljivost

Conductivity is a measure of the ability of a material to conduct electric current.

specific heat    →   specifični toplinski kapacitet

Specific heat is the quantity of heat required to raise the temperature of one gram of a substance by one degree Celsius.

thermal pollution    →   toplinsko zagađenje

Thermal pollution is the increase in temperature of natural waters resulting from the discharge to these waters of hot effluents from industrial and power plants. The higher temperatures reduce the concentration of dissolved oxygen.

heat capacity    →   toplinski kapacitet

Heat capacity is defined in general as dQ/dT, where dQ is the amount of heat that must be added to a system to increase its temperature by a small amount dT. The heat capacity at a constant pressure is C_p = (∂H/∂T)_p; that at a constant volume is C_V = (∂E/∂T)_V, where H is enthalpy, E is internal energy, p is pressure, V is volume, and T is temperature. An upper case C normally indicates the molar heat capacity, while a lower case c is used for the specific (per unit mass) heat capacity.

thermal expansion    →   toplinsko rastezanje

Thermal expansion is a change in dimensions of a material resulting from a change in temperature. All objects change size with changes in temperature. The change ΔL in any linear dimension L is given by

in which α is the thermal coefficient of linear expansion, L_o is the initial or reference dimension at temperature T_o (reference temperature) and ΔT is change in temperature which causes the change in dimension.

The change ΔV in the volume of a sample of solid or liquid is

Here γ is coefficient of volume expansion, V_o is the volume of the sample at temperature T_o and ΔV is the change in volume over the temperature range ΔT. With isotropic substances, the coefficient of volume expansion can be calculated from the coefficient of linear expansion: γ = 3α.

thermal resistance    →   toplinski otpor

Heat always flows from a higher to a lower temperature level. The driving force for the heat flux lies in the temperature difference ΔT between two temperature levels. Analogous to Ohm’s law, the following holds:

where H = dQ/dt is heat flux, measured in watts, ΔT is temperature difference across the thermal resistance, measured in kelvin, and R_th is thermal resistance, measured in K/W.

For example, suppose there were two houses with walls of equal thickness; one is made of glass and the other of asbestos. On a cold day, heat would pass through the glass house much faster. The thermal restistance of asbestos is then higher than of glass.

If the thermal Ohm’s law is divided by the heat capacity C, Newton’s law of cooling is obtained:

where dT/dt is rate of cooling or heating, measured in K s^-1, and C is heat capacity, measured in J K^-1.

bismuth    →   bizmut

Bismuth was discovered by Claude Geoffroy (France) in 1753. The origin of the name comes from the German words Weisse Masse meaning white mass; now spelled wismut and bisemutum. It is hard, brittle, steel-grey metal with a pink tint. Stable in oxygen and water. Dissolves in concentrated nitric acid. Bismuth can be found free in nature and in minerals like bismuthine (Bi₂S₃) and in bismuth ochre (Bi₂O₃) Main use is in pharmaceuticals and low melting point alloys used as fuses.

copper    →   bakar

Copper has been known since ancient times. The origin of the name comes from the Latin word cuprum meaning the island of Cyprus famed for its copper mines. It is malleable, ductile, reddish-brown metal. Resistant to air and water. Exposed surfaces form greenish carbonate film. Pure copper occurs rarely in nature. Usually found in sulfides as in chalcopyrite (CuFeS₂), coveline (CuS), chalcosine (Cu₂S) or oxides like cuprite (Cu₂O). Most often used as an electrical conductor. Also used in the manufacture of water pipes. Its alloys are used in jewellery and for coins.

metallic glass    →   metalno staklo

Certain alloys can solidify by extremely rapid cooling out of melt without formation of a crystal lattice, that is in the amorphous form - such, amorphous alloys are so called metallic glasses. The alloy of zirconium, beryllium, titanium, copper, and nickel is one of the first metallic glasses that can be made in bulk and formed into strong, hard, useful objects.

Unlike pure metals and most metal alloys, metallic glasses have no regular crystalline structure. This lack of long range order or microstructure is related to such desirable features as strength and low damping which is one reason why the premier use for zirconium-based metallic glass is in the manufacture of expensive golf club heads. Metallic glasses can be quite strong yet highly elastic, and they can also be quite tough (resistant to fracture). Even more interesting are the thermal properties; for instance, just like an oxide glass, there is a temperature (called the glass transition temperature) above which a metallic glass becomes quite soft and flows easily. This means that there are lots of opportunities for easily forming metallic glasses into complex shapes.