CHEMISTRY GLOSSARY

atmospheric pressure    →   atmosferski tlak

Atmospheric pressure is the pressure exerted by weight of the air above it at any point on the earth’s surface. At sea level the atmosphere will support a column of mercury about 760 mm high. This decreases with increasing altitude. The standard value for the atmospheric pressure at sea level in SI units is 101 325 Pa.

atomic clock    →   atomski sat

Atomic clock is an apparatus for standardizing time based on periodic phenomena within atoms or molecules (ammonia clock; caesium clock).

boiling point    →   vrelište

Boiling point is the temperature at which the vapour pressure of a liquid is equal to the external pressure on the liquid. The standard boiling point is the temperature at which the vapour pressure of a liquid equals standard pressure (101 325 Pa).

D-lines    →   D-linije

D-lines are two close lines in the yellow region of the spectrum of sodium, having wavelengths 589.6 nm (D₁) and 589.0 nm (D₂). They were labeled as feature D in the solar spectrum by German optician Joseph von Fraunhofer (1787-1826). As they a prominent and easily recognized they are used as a standard in spectroscopy.

heat of formation    →   toplina nastajanja

Heat of formation or enthalpy of is formation the heat evolved or absorbed when one mole of a compound is formed in its standard state from its constituent elements.

automatic burette    →   automatska bireta

Automatic burette is used for series of tests. It is connected with a bottle which contains the titration solution. The air is pumped into the bottle by a small rubber air pump, created the pressure in the bottle which the rises the solution to the top of burette. When the the burette is full, the valve is released, the pressure in the bottle falls and the burette automatically sets itself to zero. Work with automatic burettes is by far faster and the consumption of standard solution is smaller.

Born-Haber cycle    →   Born-Haberov kružni proces

Born-Haber cycle is a cycle of reactions used for calculating the lattice energies of ionic crystalline solids. For a compound MX, the lattice energy is the enthalpy of the reaction

The standard enthalpy of formation of the ionic solid is the enthalpy of the reaction

The cycle involves equating this enthalpy (which can be measured) to the sum of the enthalpies of a number of steps proceeding from the elements to the ionic solid. The steps are:

1) Atomization of the metal

2) Atomization of the nonmetal

3) Ionisation of the metal

This is obtained from the ionisation potential.

4) Ionisation of the nonmetal

This is electron affinity.

5) Formation of the ionic solids

Equation of the enthalpies gives

from which ΔH_L can be found.

stp    →   stp

STP (or NTP) is abbreviation for standard (normal) temperature (273.15 K or 0 °C) and pressure (10⁵ Pa). These conditions are used when comparing the properties of gases.

titrant    →   titrant

Titrant is the substance that quantitatively reacts with the analyte in a titration. The titrant is usually a standard solution added carefully to the analyte until the reaction is complete. The amount of analyte is calculated from the volume and concentration of titrant required for the complete reaction.

Bunsen burner    →   Bunsenov plamenik

Bunsen burner is a standard source of heat in the laboratory. German chemist Roberts Bunsen (1811-1899) improved the burner's design, which had been invented by Faraday, to aid his endeavors in spectroscopy. The Bunsen burner has a vertical metal tube through which a fine jet of fuel gas is directed. Air is drawn in through airholes near the base of the tube and the mixture is ignited and burns at the tube’s upper opening. The flow of this air is controlled by an adjustable collar on the side of the metal tube. When the whole is closed a yellow safety flame is displayed. Where as when the whole is open it displays a power dull blue flame with a faint blue outer flame with a vibrant blue core used u for combustion and hearting. The flame can reach temperatures of 1 500 °C.