CHEMISTRY GLOSSARY

standard    →   standard

Standards are materials containing a known concentration of an analyte. They provide a reference to determine unknown concentrations or to calibrate analytical instruments.

The accuracy of an analytical measurement is how close a result comes to the true value. Determining the accuracy of a measurement usually requires calibration of the analytical method with a known standard. This is often done with standards of several concentrations to make a calibration or working curve.

A primary standard is a reagent that is extremely pure, stable, has no waters of hydration, and has a high molecular weight.

A secondary standard is a standard that is prepared in the laboratory for a specific analysis. It is usually standardised against a primary standard.

tear gas    →   suzavac

Tear gases is the common name for substances which, in low concentrations, cause pain in the eyes, flow of tears and difficulty in keeping the eyes open. Tear gases are used mainly in military exercises and in riot control, etc., but have also been used as a method of warfare. Irritating gases have been used in war since ancient times but it was not until after the Second World War that a more systematic search for effective substances was started. Among a long series of substances, three have become of greater importance than the others. These substances are chloroacetophenone (codename CN), orto-chlorobenzylidene-malononitrile (CS) and dibenz(b,f)-1,4-oxazepine (CR).

technetium    →   tehnecij

Technetium was discovered by Carlo Perrier and Emilio Segre (Italy) in 1937. The origin of the name comes from the Greek word technikos meaning artificial. It is silvery-grey metal. Resists oxidation but tarnishes in moist air and burns in high oxygen environment. First synthetically produced element. Radioactive. Technetium is made first by bombarding molybdenum with deuterons (heavy hydrogen) in a cyclotron. Added to iron in quantities as low as 55 part-per-million transforms the iron into a corrosion-resistant alloy.

titar    →   titar

Titar (T) is a mass of titrated matter which is equivalent to 1 cm³ of solution. It is shown as T = 2.356 mg HCl / 1.0 cm³ NaOH, 0.1000 moldm^-3, and it is usually shown in a table form. If the concentration of used standard solution (c) differs from one outlined in the table data (c₀), the factor of correction (f) is induced

Titar is usually used in industrial operational laboratories where from titar tables mass or percentage of the ingredient in question is directly read.

water hardness    →   tvrdoća vode

Hardness is defined as the concentrations of calcium and magnesium ions expressed in terms of calcium carbonate. These minerals in water can cause some everyday problems. They react with soap and produce a deposit called soap curd that remains on the skin and clothes and, because it is insoluble and sticky, cannot be removed by rinsing.

Hard water may also shorten the life of plumbing and water heaters. When water containing calcium carbonate is heated, a hard scale is formed that can plug pipes and coat heating elements. Scale is also a poor heat conductor. With increased deposits on the unit, heat is not transmitted to the water fast enough and overheating of the metal causes failure. Build-up of deposits will also reduce the efficiency of the heating unit, increasing the cost of fuel.

There are two types of water hardness, temporary and permanent.

Temporary Hardness is due to the bicarbonate ion, HCO₃^-, being present in the water. This type of hardness can be removed by boiling the water to expel the CO₂, as indicated by the following equation:

Permanent hardness is due to calcium and magnesium nitrates, sulphates, and chlorides etc. This type of hardness cannot be eliminated by boiling.

water ion product    →   ionski produkt vode

Water ion product (K_w) is a concentration product of hydrogen and hydroxide ions. For the reaction:

the equilibrium expression would be:

Note that all pure liquid terms are omitted, hence H₂O does not appear in the denominator. At 25 °C, K_w = 1.0×10^-14 mol²dm^-6 = (K_a)(K_b)

Winkler’s method    →   Winklerova metoda

Winkler’s method was once a common method used to determine the dissolved oxygen concentration by titration. Now rarely used due to the accuracy and low price of oxygen meters.

The water sample is first treated with excess manganese(II) sulfate solution and then with an alkaline solution of potassium iodide. The Mn(OH)₂ initially formed reacts with the dissolved oxygen. The amount of MnO(OH)₂ formed is determined by reaction with iodide ion in acidic solution. The iodine formed may be titrated against standard thiosulfate solution, using starch as an indicator.

CO2 ion selective electrode    →   CO2 ion selektivna elektroda

The carbon dioxide ion selective electrode uses a gas-permeable membrane to separate the sample solution from the electrode internal solution. Dissolved carbon dioxide in the sample solution diffuses through the membrane until an equilibrium is reached between the partial pressure of CO₂ in the sample solution and the CO₂ in the internal filling solution. In any given sample the partial pressure of carbon dioxide will be proportional to the concentration of carbon dioxide. The diffusion across the membrane affects the level of hydrogen ions in the internal filling solution:

The hydrogen level of the internal filling solution is measured by the pH electrode located behind the membrane. The internal filling solution contains a high concentration of sodium bicarbonate (e.g. 0.1 mol/L NaHCO₃) so that the bicarbonate level can be considered constant.