CHEMISTRY GLOSSARY

practical salinity    →   praktični salinitet

Practical salinity S_P is defined on the Practical Salinity Scale of 1978 (PSS-78) in terms of the conductivity ratio K₁₅ which is the electrical conductivity of the sample at temperature t₆₈ = 15 °C and pressure equal to one standard atmosphere, divided by the conductivity of a standard potassium chloride (KCl) solution at the same temperature and pressure. The mass fraction of KCl in the standard solution is 0.0324356 (32.4356 g of KCl in 1 kg of solution). When K₁₅ = 1, the Practical Salinity P S is by definition 35. The conductivity of that reference solution is C(35,1568,0) = 42.914 mS/cm = 4.2914 S/m (Siemens per meter). Note that Practical Salinity is a unit-less quantity. Though sometimes convenient, it is technically incorrect to quote Practical Salinity in "psu". When K₁₅ is not unity, S_P and K₁₅ are related by the PSS-78 equation

At a temperature of t₆₈ = 15 °C, R_t is simply K₁₅ and Practical Salinity S_P can be determined from the above equation. For temperatures other than t₆₈ = 15 °C, Practical Salinity S_P is given by the following function of R_t (k = 0.0162)

solubility product constant    →   konstanta produkta topljivosti

Solubility product constant (K_sp) (or the solubility product) is the product of the molar concentrations of the constituent ions, each raised to the power of its stoichiometric coefficient in the equilibrium equation. For instance, if a compound A_aB_b is in equilibrium with its solution

the solubility product is given by

standard electrode potential    →   standardni elektrodni potencijal

Standard electrode potential (E°) (standard reduction potentials) are defined by measuring the potential relative to a standard hydrogen electrode using 1 mol solution at 25 °C. The convention is to designate the cell so that the oxidised form is written first. For example,

The e.m.f. of this cell is -0.76 V and the standard electrode potential of the Zn²+|Zn half cell is -0.76 V.

stoichiometric coefficient    →   stehiometrijski koeficijent

Stoichiometric coefficient (ν) is the number appearing before the symbol for each compound in the equation for a chemical reaction. By convention, it is negative for reactants and positive for products.

Stoichiometric coefficients describe the stoichiometry of the chemical reaction.

In this equation, a, b, c and d are called as Stoichiometric coefficients of the A, B, C and D respectively.

stoichiometry    →   stehiometrija

Stoichiometry is the relative proportions elements from compounds or in which substances react. Every chemical reaction has its characteristic proportions. For example, when methane unites with oxygen in complete combustion, 1 mol of methane requires 2 mol of oxygen.

At the same time, 1 mol of carbon dioxide and 2 mol of water are formed as reaction products.

Alternatively, 16 g of methane and 64 g of oxygen produce 44 g of carbon dioxide and 36 g of water.

The stoichiometric relationship between the products and reactants can be used to in calculations.

thermal resistance    →   toplinski otpor

Heat always flows from a higher to a lower temperature level. The driving force for the heat flux lies in the temperature difference ΔT between two temperature levels. Analogous to Ohm’s law, the following holds:

where H = dQ/dt is heat flux, measured in watts, ΔT is temperature difference across the thermal resistance, measured in kelvin, and R_th is thermal resistance, measured in K/W.

For example, suppose there were two houses with walls of equal thickness; one is made of glass and the other of asbestos. On a cold day, heat would pass through the glass house much faster. The thermal restistance of asbestos is then higher than of glass.

If the thermal Ohm’s law is divided by the heat capacity C, Newton’s law of cooling is obtained:

where dT/dt is rate of cooling or heating, measured in K s^-1, and C is heat capacity, measured in J K^-1.

U-tube manometer    →   U-manometar

U-tube manometer contains water or mercury in a U-shaped tube, and is usually used to measure gas pressure. One end of the U tube is exposed to the unknown pressure field (P) and the other end is connected to a reference pressure source (usually atmospheric pressure) (P_ref), shown in the schematic below.

If fluid C is the atmosphere, fluid B is the liquid in the U tube (e.g. water or mercury), and fluid A is a gas, then we can assume that ρB >> ρA, ρC. The pressure contributed by the weight of gas within the U tube can therefore be neglected. The gage pressure of the gas can be approximated by,

Winkler’s method    →   Winklerova metoda

Winkler’s method was once a common method used to determine the dissolved oxygen concentration by titration. Now rarely used due to the accuracy and low price of oxygen meters.

The water sample is first treated with excess manganese(II) sulfate solution and then with an alkaline solution of potassium iodide. The Mn(OH)₂ initially formed reacts with the dissolved oxygen. The amount of MnO(OH)₂ formed is determined by reaction with iodide ion in acidic solution. The iodine formed may be titrated against standard thiosulfate solution, using starch as an indicator.

X-ray diffraction    →   rendgenska difrakcija

The regular array of atoms in a crystal is a three-dimensional diffraction grating for short-wavelength waves such as X-rays. The atoms are arranged in planes with interplanar spacing d. Diffraction maxima occur in the incident direction of the wave, measured from the surface of a plane of atoms, and the wavelength λ of the radiation satisfy Braggs’s law: